| |
| | |

Printer Forum   

 Forgot password?
 register
Search
View: 2805|Reply: 17

Anyone with a Xerox 800/1000 running Pacesetter Stock?

[Copy link]

Post time: 2013-4-27 14:22:22 |Show all posts
Anyone with a Xerox 800/1000 running Pacesetter Stocks as your main house stock? If you are or were, are you having skewing problems?
Constant 077-134 errors/jams?
My machine has gotten finicky and not holding front to back registration.
The machine doesn't seem to be holding any adjustments made in the profile section.

What have been your experiences with this paper? Or are you having similar issues and running a different stock, if so what?

Post time: 2013-4-28 16:06:01 |Show all posts
Hmm we got those replace about a year ago, its an old fix.

Post time: 2013-4-28 14:58:43 |Show all posts
By coincidence Fuji Xerox arrived with new steel alignment top rollers replacing the worn white plastic rollers.
The white ones were worn down to different diameters which might account for the mis-alignment of the prints.
But because there was replacement (improved) parts available, perhaps it was a known issue.
Frankly I don't care but it would have been helpful to hear that it was a known issue and that a fix was in the works. That way we probably would have had a lot less downtime chasing the wrong solution.
So if anyone else is having registration issues, insist on replacing the plastic rollers with the steel rollers.

Post time: 2013-4-28 13:10:00 |Show all posts
Thank you. I'm not fully convinced that the FWA is the culprit, but we have had most of the feeders and alignment parts replaced and the problems keep recurring.

Post time: 2013-4-28 11:28:34 |Show all posts
yes we had a full width array fitted a few month after the printer was installed. Im really pleased with the allignment profiles and do not suffer the same problems as you do.

Post time: 2013-4-28 09:49:17 |Show all posts
I've been running a Xerox 1000 since August 2010. All types of stocks except Nevertear. Registration, skewing, tombstoning, front to back alignment all OK and we were very happy. Fuji Xerox have used us as a reference site although not recently.
But in August 2012 we had a Full Width Array fitted and since that time it is a daily battle to keep registration under control. Sometimes it takes 5 tries with the Full Width Array to get the alignment correct.
Lots of service calls, Creo software updates, tray calibrations (we run 4 trays) and the alignment can be off on the next job.
My next attempt will be to see if we can disable the Full Width Array to see if that is the cause of the problem.
Has anyone else had a Full Width Array retro-fitted?

Post time: 2013-4-28 08:34:14 |Show all posts
Boa Tarde Mrs.
Alguem pode me indicar algum site dos EUA onde eu possa comprar peças para Xerox1000 (Press1000), visto que no brasil o custo do consumivel da mesma esta muito alto.

Post time: 2013-4-28 07:16:35 |Show all posts
boa Tarde wagsgraphx

Voce ja verificou os sensores do registro, se o modulo do registro esta se movimento corretamente, a configuração do formato do papel se esta correta.
A plataforma onde passa o papel não tem nada segurando o papel a mesma não esta aspera (Defeito de fabricação).
A Falha acontece em qual gramatura?

Post time: 2013-4-28 05:34:11 |Show all posts
boa Tarde wagsgraphx

Voce ja verificou os sensores do registro, se o modulo do registro esta se movimento corretamente, a configuração do formato do papel se esta correta.
A plataforma onde passa o papel não tem nada segurando o papel a mesma não esta aspera (Defeito de fabricação).
A Falha acontece em qual gramatura?

Post time: 2013-4-28 04:08:45 |Show all posts
Xerox is planning on replacing my registration unit. Nothing they have done so far has corrected the problem. I constantly have to back off Aligner pressure during the run to stop jams, then the sheet starts skewing on F/B registration.

Post time: 2013-4-28 02:57:56 |Show all posts
I just replaced a belt because of a crescent moon shape cut that developed in my belt. Did not see it initially when it was installed.

Post time: 2013-4-28 01:27:58 |Show all posts
I havent seen that on any of our belts, so yeah, probaly a manufacturing fault

Post time: 2013-4-27 23:31:09 |Show all posts
Boa Tarde senhores
Ao substituir a correia do fusor (064K93300), surgiu uma marca na mesma (bolha) apos aquecer, o que ficou bem visivel na impressão, sera que alguém ja teve este problema, para mim parece defeito de fabricação?

Post time: 2013-4-27 21:46:02 |Show all posts
First thing I do when at an X1000/800 with this problem is to replace the three aligner rolls and remove the de-fluff pads which can cause drag.
Does the skewing/jamming happen more from the HCF or from trays 1 & 2 or only when duplexing.

These rolls are from the 2060 design and IMOO are only just capable of handleing the heavier stocks at a higher speed but I do have success if replaced and kept clean regularly.  Any build up tends to 'weld' it's self to the rolls causing them to go shiny and lose their grip

I have had the problem but only from the HCF.  It was corrupt NVM's causing it and running DC126 in CSE diag solved it.

I don't know how your service guys run your sites but we keeps these rolls on all of the lockers

Also check that you are not running the HP Indigo version of the stock.  There may be two versions.  One for Indigo and another for Xerox Fuser type printers.  They are not compatible.  If it says HP Indigo certified it is not the correct stock even if it says on the packet Xerox approved.  Alot of mills have been doing this to increase there sales volume across the range

--
Mark

Post time: 2013-4-27 19:51:52 |Show all posts
The only xerox stock i ran was nevertear, it was horrible sometimes aswell.. Id like to think when you get on the first week training as a xerox tech they tell you different ways to convince the customer its their paper which is the cause of the problem. However my experience is, since we got a onsite tech i often tell him to go look up the fault codes and find a solution, and he usually do by replacing og cleaning something. So if i where you i would tell them to fix instead of blaming the paper, rough them up  

Post time: 2013-4-27 18:42:15 |Show all posts
After 2 years of running this thing I have played with every setting available. Ever since they switched out to the silver aligner rollers all my pressure settings have been minus. The problem is the greater the minus setting the more chance you have of the sheet skewing and your f/b registration being off. I clean all my sensors and all the rubber rollers that touch the paper. I didn't used to have this problem, now it's a daily battle.
Even when I go into the profiles and change settings to compensate for what the press is doing, they don't hold and more corrections have to be made.
I'm constantly chasing f/b registration and skewing.
Of course Xerox wants to blame it on the paper. That's why I'd like to know what paper brand people are running.
Is anybody running Xerox stock and still having these issues?

Post time: 2013-4-27 17:39:28 |Show all posts
to be honest we have alot of jams on our cp800, the worst is the 4 minutes warm up from every jam which involves the fuser(!!!).
Try as Claudinei to change the roller pressure. The most of our heavier stock is set to -36
Check to clean the assist sensor in the registration, and the paper path sensor right after the transfer aswell

Post time: 2013-4-27 16:05:00 |Show all posts
ola amigo, você já tentou entrar como administrador e mudar a pressão dos rolos (ranger -40 - 0 - +40) posição original é zero mas mudando estas provavelmente ira funcionar normalmente. esta falha ocorre principalmente em papel acima 250gm
You have to log in before you can reply Login | register

Advertise on OASQ.COM| Contact us| Archive| OASQ

2019-1-18 06:45 GMT-8

Powered by Discuz! 7.2

Release 20121101, © 2001-2019 OASQ.

To Top